Adventure Easel Shaker Card with Kaylee

'Road Trip Adventure' Easel/Shaker Card
Card Size - 10.5 cm x 14.8 cm  (1/4 of an A4 sheet)

Hello Everyone,

Welcome to my next project for Couture Creations using the 

wonderful Sunburnt Country Collection.

This project is an easel card with a difference - I added a shaker to the front panel.

1.  I started die-cutting with the nesting dies.   I numbered the dies as 1 from the centre then outwards. To create the frame for the shaker, I taped number 4 and 5 dies together and cut 2 out of the foam sheet and one from the red cardstock.  (The inner waste cut from the red cardstock is used as a label for the inside of the card).   I then used die 5 to cut the acetate and from sheet 11A as shown. Die 6 was used for sheet 8A and red cardstock.  I cut the red cardstock in half lengthwise to create a mat for the pattern paper sheet.	2.  Prepare all the elements with this die set.  The 'Road Trip' stamp is embossed with white embossing powder.  I stamped the 'Adventure' stamp onto the Acetate but later changed it to white embossing  powder as well.
3.  Die-cut white card with number 7 die to create a card front panel.  For the Easel base, trim the white card to 14.5cm x 21cm, divide by half, score and fold.   Keep it folded and place the die so it overlaps the fold.  Once it is die-cut, divide one side by half,  score and fold.   Apply double-sided tape and glue to the lower part of the double-folded side front only.  Place the front panel onto this section.	4.  Using a water brush I coloured the glass beads with a bit of red ink and water to go into the shaker.
5.  I die-cut the remaining pieces and inked their edges with brown ink. Then fussy cut another flower image from the patterned paper and decoupaged it on top of the flower on the panel.  Place cardboard between the panels before adhering them.  Glue the shaker pieces together.   In the shaker I added beads, sequins and die-cut kangaroos.	6.  All the pieces just need to be glued in place as shown to finish.

Sideways view of fold

Inside Label

The Shaker with the Kangaroos, Sequins and Beads

Folded Flat ready for mailing

1.  I started die-cutting with the nesting dies.   I numbered the dies as 1 from the centre then outwards.

To create the frame for the shaker, I taped number 4 and 5 dies together and cut 2 out of the foam sheet and one from the red cardstock.  (The inner waste cut from the red cardstock is used as a label for the inside of the card).  

I then used die 5 to cut the acetate and from sheet 11A as shown.

Die 6 was used for sheet 8A and red cardstock.  I cut the red cardstock in half lengthwise to create a mat for the pattern paper sheet.

2.  Prepare all the elements with this die set.  The 'Road Trip' stamp is embossed with white embossing powder.  I stamped the 'Adventure' stamp onto the Acetate but later changed it to white embossing  powder as well.   

3.  Die-cut white card with number 7 die to create a card front panel.  For the Easel base, trim the white card to 14.5cm x 21cm, divide by half, score and fold.   Keep it folded and place the die so it overlaps the fold.  Once it is die-cut, divide one side by half,  score and fold.   Apply double-sided tape and glue to the lower part of the double-folded side front only.  Place the front panel onto this section. 

4.  Using a water brush I coloured the glass beads with a bit of red ink and water to go into the shaker.

5.  I die-cut the remaining pieces and inked their edges with brown ink. Then fussy cut another flower image from the patterned paper and decoupaged it on top of the flower on the panel.  Place cardboard between the panels before adhering them.  Glue the shaker pieces together.   In the shaker I added beads, sequins and die-cut kangaroos.

6.  All the pieces just need to be glued in place as shown to finish.

                       Couture Creations Products:-

CO727278 - Sunburnt Country 6.5" x 6.5" Paper Pad, Sheet 8A & 11A

ULT157474 Die - Small Grass Tree

CO727214 Mini Die - Australia & Kangaroo

CO727220 Mini Die - Gumnuts

CO727221 Mini Die - Eucalyptus

CO727222 Mini Die - Kookaburra

CO727227 Mini Die - Acacia Branch

CO727211 Mini Stamp - Adventure

CO727210 Mini Stamp - Road Trip

CO726459 Cut, Foil & Emboss Die - Nesting Bracket Frames

CO725408 Mirror Foil Board A4 Matte Bronze

ULT200002 Cardstock - Delicate Medlar

ULT200031 Cardstock - Cypress Pine 

ULT200040 Cardstock - Chocolate

ULT200045 Cardstock - Paper Bag

ULT200067 Cardstock - Garnet

CO724824 Gocut and Emboss Machine

CO723978 Multi-Purpose Heat Tool

Other products used:  ,

White card, Acetate, White Embossing Powder, Double-sided tape, Glue, Red 2mm Foam sheet, Cardboard, Water Brush, Red Die, Sequins, Glass Beads and Muslin

 To find a store near you that stock these Couture Creations products, click on the following link:-  https://couturecreations.com.au/pages/store-locator   

My Blog Link is: Card Craft Kaylee

Thanks for joining me...

   #couturecreationsaus